DeWalt DW9107 Bedienerhandbuch PDF herunterladen (Seite 5)

d) Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with

these instructions, taking into account the working conditions and the work

to be performed. Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the manufacturer. A charger

that is suitable for one type of battery pack may create a risk of fire when

used with another battery pack.

b) Use power tools only with specifically designated battery packs. Use of any

other battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like

paper clips, coins, keys, nails, screws, or other small metal objects that

can make a connection from one terminal to another. Shorting the battery

terminals together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery; avoid

contact. If contact accidentally occurs, flush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejected from the battery may

cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power tool

is maintained.

Electrical Safety

The electric motor has been designed for one voltage range only. Always check that

the power supply corresponds to the voltage on the rating plate. 220–240 V AC

means your tool will operate on alternating current. Operation at a voltage outside this

range can cause loss of power and can result in overheating. All DEWALT tools are

factory tested; if this tool does not operate, check the power supply. Your DEWALT

tool is double insulated, therefore no earth wire is required.

• Young children and the infirm. This appliance is not intended for use by young

children or infirm persons without supervision.

– This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

– Children should be supervised to ensure that they do not play with the appliance.

• Replacement of the supply cord. If the supply cord or plug is damaged, it must

be replaced by the manufacturer or an authorised D

EWALT Service Centre in

order to avoid a hazard.

Extension Cords

CAUTION: Use only extension cords that are approved by the country’s Electrical

Authority. Before using extension cords, inspect them for loose or exposed wires,

damaged insulation and defective fittings. Replace the cord if necessary.

Tool Safety Warnings

• Hold power tool by insulated gripping surfaces, when performing an operation

where the fastener may contact hidden wiring. Fasteners contacting a “live”

wire may make exposed metal parts of the power tool “live” and could give the

operator an electric shock.

• Use clamps or another practical way to secure and support the workpiece

to a stable platform. Holding the work by hand or against your body leaves it

unstable and may lead to loss of control.

• Air vents often cover moving parts and should be avoided. Loose clothes,

jewellery or long hair can be caught in moving parts.

WARNING: We recommend the use of a residual current device with a residual

current rating of 30mA or less.

1 2 3 4 5 6 7 8 9 10 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

DeWalt DW9107 Bedienerhandbuch Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kraftschraubendreher DeWalt DW9107